manualshive.com logo in svg

Intel D815EEA2, Product Manual

Share
Download
Intel D815EEA2 Product Manual Download Page 52

Intel Desktop Boards D815EEA2, D815EPEA2, D815EFV, and D815EPFV Product Guide 

52  

 

Obtaining the BIOS Update File 

You can update to a new version of the BIOS by using the BIOS update file.  The BIOS update file 
is a compressed self-extracting archive that contains all the files you need to update the BIOS.  The 
BIOS update file contains: 

• 

New BIOS files 

• 

BIOS recovery files 

• 

Intel Flash Memory Update utility 

You can obtain the BIOS update file through your computer supplier or from the Intel World Wide 
Web site:  

http://support.intel.com/support/motherboards/desktop/

 

✏

 

NOTE 

Review the instructions distributed with the update utility before attempting a BIOS update. 

 

The Intel Flash Memory Update utility allows you to: 

• 

Update the BIOS in flash memory. 

• 

Update the language section of the BIOS. 

Saving the Current BIOS Settings 

 

1.  Boot the computer and press <F2> when you see the message: 

 

Press <F2> Key if you want to run SETUP 

2.  Save the current settings in the BIOS Setup program. 

Creating Bootable Media 

You can create bootable media with a: 

• 

CD writer 

• 

Normal diskette drive or an LS-120 diskette drive 

Creating a Bootable CD 

Follow the instructions provided with your CD writer to make a bootable CD using floppy 
emulation and bootable files.  

Summary of Contents for D815EEA2

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands