Intel D815EEA2 Product Manual Download

Page: 73 / 96

Using the Setup Program

APM Submenu

To access this menu, select Power on the menu bar, then APM.

Maintenance

Main

Advanced Security

Power

Boot

Exit

APM

ACPI

The submenu represented in Table 24 is for setting the APM features.

Table 24. APM Submenu

Feature Options Description

Power Management

•

Disabled

•

Enabled (default)

Enables or disables the APM feature.

Inactivity Timer

•

Off

•

1 Minute

•

5 Minutes

•

10 Minutes

•

20 Minutes (default)

•

30 Minutes

•

60 Minutes

•

120 Minutes

Specifies the amount of time before the computer enters
APM standby mode.

Hard Drive

•

Disabled

•

Enabled (default)

Enables power management for hard disks during APM
standby mode.

ACPI Submenu

To access this menu, select Power on the menu bar, then ACPI.

Maintenance

Main

Advanced Security

Power

Boot

Exit

APM

ACPI

The submenu represented in Table 25 is for setting the ACPI features.

Table 25. ACPI Submenu

Feature Options

Description

ACPI Suspend State

•

S1 State

•

S3 State

(default)

Specifies the ACPI sleep state.

Video Repost
(This feature is present
only when ACPI Suspend
State is set to S3)

•

Disabled (default)

•

Enabled

Allows the video BIOS to be initialized coming out of the
S3 state. Some video controllers require this option to
be enabled. This feature is present only if the ACPI
suspend state is set to S3 state.

Wake on LAN from S5

•

Stay Off (default)

•

Power On

In ACPI soft-off mode only, determines how the system
responds to a LAN wake up event when the system is in
the ACPI soft-off mode.

Summary of Contents for D815EEA2

































































































Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands

Intel D815EEA2, Product Manual

Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands