Intel D815EEA2 Page 24 Product Manual Download | Manualshive

Page: 24 / 96

background image

Intel Desktop Boards D815EEA2, D815EPEA2, D815EFV, and D815EPFV Product Guide

24

OM11632

CR6F1

STR
LED

Figure 3. Location of Standby Power Indicator (the D815EEA2 Board Is Shown)

CAUTION

Power supplies used with the board must provide enough standby current to support the Instantly
Available (ACPI S3 sleep state) configuration. If the standby current necessary to support
multiple wake events from the PCI and/or USB buses exceeds power supply capacity, the board
may lose register settings stored in memory and may not awaken properly.

✏

NOTE

1.5 A of standby current is recommended. Refer to the

Intel Desktop Board

D815EEA2/D815EPEA2 Technical Product Specification

or

Intel Desktop Board

D815EFV/D815EPFV Technical Product Specification

for more information

.

Resume on Ring

The operation of Resume on Ring can be summarized as follows:

•

Resumes operation from either the APM sleep mode or the ACPI S1 state

•

Requires only one call to access the computer

•

Detects incoming call similarly for external and internal modems

•

Requires modem interrupt be unmasked for correct operation

«
...
22
23
24
25
26
...
»

Summary of Contents for D815EEA2

































































































Reviews:

No comments

Related manuals for D815EEA2

Brand: D-Link Pages: 15

Brand: NEC Pages: 72

ELECTRA ELITE IPK II

Brand: NEC Pages: 617

VERSA DOCK - SERVICE

Brand: NEC Pages: 8

Brand: Vonets Pages: 8

Brand: Paradyne Pages: 1

Brand: Roland Pages: 12

Brand: ESD Pages: 28

Brand: Baicells Pages: 10

PXI PXITM -1000

Brand: National Instruments Pages: 55

Brand: 3Com Pages: 53

Brand: Altera Pages: 40

Brand: Milesight Pages: 15

Brand: Lanpro Pages: 3

Brand: Lefroy Brooks Pages: 10

ExpressCard 11-in-1 Reader/Writer

Brand: SIIG Pages: 8

ACL-8112 Series

Brand: NuDAQ Pages: 92

Brand: ELSA Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands