Intel D815EEA2 Page 70 Product Manual Download

Page: 70 / 96

Intel Desktop Boards D815EEA2, D815EPEA2, D815EFV, and D815EPFV Product Guide

Video Configuration Submenu

To access this menu, select Advanced on the menu bar, then Video Configuration.

Maintenance

Main

Advanced

Security

Power

Boot

Exit

PCI

Configuration

Boot

Configuration

Peripheral

Configuration

IDE

Configuration

Diskette

Configuration

Event Log Configuration

Video Configuration

The submenu represented in Table 21 is for configuring the video features.

Table 21. Video Configuration Submenu

Feature Options Description

Primary Video Adapter

•

AGP (default)

•

PCI

Selects primary video adapter to be used during
boot.

AGP Hardware Detected No Options

Integrated

indicates that the onboard graphics

subsystem is enabled on the D815EEA2 and
D815EFV boards only.

1x AGP Card

2x AGP Card

, or

4x AGP Card

indicates that the BIOS has detected a 1x, 2x, or 4x
AGP card. Installing an add-in AGP card disables
the onboard graphics subsystem on the D815EEA2
and D815EFV boards.

Summary of Contents for D815EEA2

































































































Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands

Intel D815EEA2, Product Manual

Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands