Intel D815EEA2 Product Manual Download

Page: 69 / 96

Using the Setup Program

Event Log Configuration Submenu

To access this menu, select Advanced on the menu bar, then Event Log Configuration.

Maintenance

Main

Advanced

Security

Power

Boot

Exit

PCI

Configuration

Boot

Configuration

Peripheral

Configuration

IDE

Configuration

Diskette

Configuration

Event Log Configuration

Video

Configuration

The submenu represented by Table 20 is used to configure the event logging features.

Table 20. Event Log Configuration Submenu

Feature Options Description

Event Log

No options

Indicates if there is space available in the event log.

Event Log Validity

No options

Indicates if the contents of the event log are valid.

View Event Log

[Enter]

Displays the event log.

Clear All Event Logs

•

No (default)

•

Yes

Clears the event log after rebooting.

Event Logging

•

Disabled

•

Enabled (default)

Enables logging of events.

Mark Events As Read

•

Yes

(default)

•

Marks all events as read.

Summary of Contents for D815EEA2

































































































Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands

Intel D815EEA2, Product Manual

Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands