Intel D815EEA2 Product Manual Download | Manualshive

Page: 93 / 96

background image

Regulatory Compliance

93

Installation Precautions

When you install and test the desktop board, observe all warnings and cautions in the installation
instructions.

To avoid injury, be careful of:

•

Sharp pins on connectors

•

Sharp pins on printed circuit assemblies

•

Rough edges and sharp corners on the chassis

•

Hot components (like processors, voltage regulators, and heat sinks)

•

Damage to wires that could cause a short circuit

Observe all warnings and cautions that instruct you to refer computer servicing to qualified
technical personnel.

Installation Instructions

CAUTION

Follow these guidelines to meet safety and regulatory requirements when installing this board
assembly.

Read and adhere to all of these instructions and the instructions supplied with the chassis and
associated modules. If the instructions for the chassis are inconsistent with these instructions or
the instructions for associated modules, contact the supplier’s technical support to find out how
you can ensure that your computer meets safety and regulatory requirements. If you do not follow
these instructions and the instructions provided by chassis and module suppliers, you increase
safety risk and the possibility of noncompliance with regional laws and regulations.

Ensure Electromagnetic Compatibility (EMC) Compliance

Before computer integration, make sure that the power supply and other modules or peripherals, as
applicable, have passed Class B EMC testing and are marked accordingly.

In the installation instructions for the host chassis, power supply, and other modules pay close
attention to the following:

•

Product certifications or lack of certifications

•

External I/O cable shielding and filtering

•

Mounting, grounding, and bonding requirements

•

Keying connectors when mating the wrong connectors could be hazardous

If the power supply and other modules or peripherals, as applicable, are not Class B EMC
compliant before integration, then EMC testing is required on a representative sample of the newly
completed computer.

«
...
91
92
93
94
95
...
»

Summary of Contents for D815EEA2

































































































Reviews:

No comments

Related manuals for D815EEA2

Brand: LAWO Pages: 154

Brand: M86 Security Pages: 46

INTERNET PRIVACY PROTECTION

Brand: AlphaShield Pages: 49

Brand: RAK Pages: 30

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Brand: Intel Pages: 86

Brand: AMX Pages: 1

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Brand: Teridian Pages: 2

NexXxoS GPX-N 1070-M08

Brand: Alphacool Pages: 4

Brand: ICP Pages: 111

Brand: NEC Pages: 26

Brand: Yeastar Technology Pages: 2

VDA-NVR2108W4KS2

Brand: Dahua Technology Pages: 363

IQ Switch IQS128

Brand: Azoteq Pages: 4

Brand: Orcomm Pages: 10

Brand: Hama Pages: 10

CNPS7000B Series

Brand: ZALMAN Pages: 9

3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card...

Brand: 3Com Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands