Intel D815EEA2 Product Manual Download

Page: 62 / 96

Intel Desktop Boards D815EEA2, D815EPEA2, D815EFV, and D815EPFV Product Guide

PCI Configuration Submenu

To access this submenu, select Advanced on the menu bar, then PCI Configuration.

Maintenance

Main

Advanced

Security

Power

Boot

Exit

PCI Configuration

Boot

Configuration

Peripheral

Configuration

IDE

Configuration

Diskette

Configuration

Event Log Configuration

Video

Configuration

The submenu represented by Table 14 is for configuring the IRQ priority of PCI slots individually.

Table 14. PCI Configuration Submenu

Feature Options

Description

PCI Slot 1 IRQ Priority

•

Auto (default)

•

Allows selection of IRQ priority. IRQ Priority selections for
PCI slots 1 and 5 are linked. Selections made to PCI
Slot 1 IRQ Priority are repeated in PCI Slot 5 IRQ Priority.

PCI Slot 2 IRQ Priority

•

Auto (default)

•

Allows selection of IRQ priority and S5 wake.

PCI Slot 3 IRQ Priority

•

Auto (default)

•

Allows selection of IRQ priority.

PCI Slot 4 IRQ Priority

(Note)

•

Auto (default)

•

Allows selection of IRQ priority.

PCI Slot 5 IRQ Priority

(Note)

No options

Always set to Auto.

Note: PCI slot 4 and slot 5 are available only on D815EEA2 and D815EPEA2 boards.

Summary of Contents for D815EEA2

































































































Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands

Intel D815EEA2, Product Manual

Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands