Intel D815EEA2 Product Manual Download

Page: 11 / 96

Desktop Board Features

Manufacturing Options

Table 3 describes the manufacturing options of the boards.

Table 3.

Manufacturing Options

Characteristic Specification

Communication and
Networking Riser (CNR)
Connector

One CNR connector:

•

Slot shared with PCI bus connector 5 on D815EEA2 and D815EPEA2 boards.

•

Slot shared with PCI bus connector 3 on D815EFV and D815EPFV boards.

Digital Video Output
(DVO)

Interface for optional Digital Visual Interface (DVI) card to support Flat Panel,
Digital CRT, or TV out (D815EEA2 and D815EFV boards only).

Front Panel Audio
Connector

Routes mic in and line out to the front panel.

Front Panel USB
Connector

Provides access to two additional USB ports, routed through the optional SMSC
LPC47M142 LPC bus I/O controller.

Integrated LAN
Subsystem

Intel

82562ET that provides a basic interface to the RJ-45 connector with

integrated LED’s located on the back panel.

I/O Controller

SMSC LPC47M142 LPC bus I/O controller

Wake on LAN

†

(WOL)

Technology Connector

Support for system wake up using an add-in network interface card with remote
wake up capability.

✏

NOTE

For information about Intel

desktop boards, including technical product specifications, BIOS

upgrades, and device drivers, go to the Intel World Wide Web site at:

http://support.intel.com/support/motherboards/desktop

Summary of Contents for D815EEA2

































































































Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands

Intel D815EEA2, Product Manual

Search results

Summary of Contents for D815EEA2

Reviews:

Related manuals for D815EEA2

Brands by name

Popular brands