Intel Agilex Configuration User Manual Download Page 18

Page: 18 / 196

Reconfiguration Timing

The second event the timing diagram illustrates the Intel Agilex device reconfiguration. If you change the

MSEL

setting after

power-on, you must power-cycle the Intel Agilex. Power cycling forces the SDM to sample the

MSEL

pins before reconfiguring

the device.

The numbers in the Reconfiguration part of the timing diagram mark the following events:
1. The external host drives

nCONFIG

signal low.

2. The SDM initiates device cleaning.
3. The SDM drives the

nSTATUS

signal low when device cleaning is complete.

4. The external host drives the

nCONFIG

signal high to initiate reconfiguration.

5. The SDM drives the

nSTATUS

signal high signaling the device is ready for reconfiguration and starts to reconfigure.

Configuration Error

The numbers in the Configuration Error part of the timing diagram mark the following events:
1. The SDM drives

nSTATUS

signal low for

1 ms -0.5 ms/+9.5 ms

to indicate a configuration error. The Intel Agilex

device does not assert

CONF_DONE

indicating that configuration did not complete successfully.

2. The SDM enters the error state. During the error state,

nCONFIG

should be in the high state. The application must drive

nCONFIG

from high to low and then from low to high to restart configuration.

3. The SDM enters the idle state. The external host deasserts

nCONFIG

. The device is ready for reconfiguration by driving a

low to high transition on

nCONFIG

. You can also power cycle the device by following the device power down sequence.

Note: The

nCONFIG

signal can only change levels when it has the same value as

nSTATUS

. This restriction means that

when

nSTATUS

= 1,

nCONFIG

can transition from 1 to 0. When

nSTATUS

= 0,

nCONFIG

can transition from 0 to 1.

Apart from error reporting,

nSTATUS

only changes to follow

nCONFIG

Power Supply Status

The power-on reset (POR) holds the Intel Agilex device in the reset state until the power supply outputs are within the
recommended operating range.

RAMP

defines the maximum power supply ramp time. If POR does not meet the

RAMP

time,

the Intel Agilex device I/O pins and programming registers remain tri-stated.

For more information about POR refer to the Intel Agilex Power Management User Guide. For more information about

RAMP

refer to the Intel Agilex datasheet.

2. Intel Agilex Configuration Details

UG-20205 | 2019.10.09

Intel

Agilex

™

Configuration User Guide

Send Feedback

Summary of Contents for Agilex





































































































































































































Search results

Summary of Contents for Agilex

Reviews:

Intel Agilex, Configuration User Manual, Page: 18 / 196

Search results

Summary of Contents for Agilex

Reviews: