Intel 460GX Software Developer’S Manual Download Page 86 | Manualshive

Page: 86 / 294

background image

System Address Map

4-6

Intel® 460GX Chipset Software Developer’s Manual

•

I/O addresses used for VGA controllers: 03B0h-03BBh and 03C0h-03DFh. These addresses
are specifically decoded so they can be mapped to the PCI bus specified by the VGA Space
Register. An I/O access must be contained fully within the VGA I/O range to be remapped
(e.g. an I/O read spanning 03BBh and 03BCh would not be remapped because it crosses the
VGA I/O range). Posting of this range for writes is controlled by the state of the I/O posting
enable bit in the Software-Defined Configuration Register.

•

I/O addresses used for the PCI Configuration Space Enable (CSE) protocol. The I/O addresses
0CF8h and 0CFCh are specifically decoded as part of the CSE protocol. These addresses, like
the I/O addresses less than 100h, are treated as “defer only” addresses.

•

Posting for all other I/O addresses is controlled by the state of the I/O posting enable bit in the
Software-Defined Configuration Register. If this bit is set, I/O writes are posted. If this bit is
not set, all I/O writes are deferred. I/O reads are always deferred.

Note, the 460GX chipset does not support ISA expansion aliasing. The IFB supports a full I/O
space decode, so the compatibility issue will be drivers that rely on the I/O aliasing behavior.

Historically, the 64k I/O space actually was 64k+3 bytes. For the extra 3 bytes, A#[16] is asserted.
The 460GX chipset decodes only A#[15:3] when the request encoding indicates an I/O cycle.
Therefore accesses with A#[16] asserted are decoded as if they were accesses to address 0 and will
be forwarded to the compatibility bus. Since they look like accesses less than 100h, they are always
deferred rather than posted. The full address is sent to the PXB and on to the compatibility PCI bus,
which therefore has PCI address bit A#[16] active.

At power-on, all I/O accesses are mapped to the compatibility bus. An I/O access is never
forwarded inbound by the chipset. The I/O address map is shown in

Figure 4-3

.

Figure 4-3. System I/O Address Space

0000

FFFF

1000

2000

3000

4000

Segment 0

Compatibility

Bus Only

Segment 1

Segment 2

Segment 3

Segment 15

F000

+3 bytes

1_0003

(Decoded

as 0_000X)

«
...
84
85
86
87
88
...
»

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

Brand: Aleratec Pages: 12

Brand: Hama Pages: 12

Brand: TP-Link Pages: 2

Brand: LogLogic Pages: 30

Aquaduct 240 eco

Brand: Aqua Computer Pages: 20

Advanced Flame 1.0

Brand: Eastern Voltage Research Pages: 12

Brand: ADTRAN Pages: 9

Brand: Xtreme Pages: 83

Serial Attached SCSI (SAS) Expander Card

Brand: Adaptec Pages: 26

EK-Quantum Vector TUF RX 6800

Brand: ekwb Pages: 14

STM32MP157 Series

Brand: ST Pages: 47

Brand: IEI Technology Pages: 116

Brand: Arduino Pages: 10

Brand: RadiSys Pages: 6

Brand: Linksys Pages: 37

Brand: Radionics Pages: 100

PMP/PTP 450 Series

Brand: Cambium Networks Pages: 155

Brand: ProCurve Pages: 406

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands