Intel 460GX Software Developer’S Manual Download Page 129 | Manualshive

Page: 129 / 294

background image

Intel® 460GX Chipset Software Developer’s Manual

6-31

Data Integrity and Error Handling

(

DPE

) bit is asserted. Regardless, if the transaction is a read, the

PCISTS

register’s Parity Error

(

PE

) bit will be set. Additionally, address, command, and data related information is logged in the

FEPCIAL

and

FEPCIL

registers if the error is the first error observed by the WXB.

6.12.8.1.6 Other Violations

The PCI specification identifies numerous cases that are violations of the PCI protocol. Other than
the cases identified above, the WXB makes no attempt to check for such violations. Response to
such violations is undefined. Refer to the PCI specification for a complete description of the
required PCI protocol.

6.12.8.2

WXB as Target

6.12.8.2.1 Illegal PCI Request Type

The WXB will not claim transactions that use an illegal or unrecognized request type.

6.12.8.2.2 Target Disconnect

The WXB will issue a target disconnect under the following circumstances:

•

After the first data transfer if the transaction is using an unrecognized addressing mode (the
WXB will only support linear incrementing as a target),

•

On reads, when no more data is available in the read buffers, and

These conditions are not treated as an error, and will not be logged or reported.

6.12.8.2.3 Target Retry

The WXB will issue a target retry when:

•

A read request is to an address that has already been accepted as a delayed transaction (i.e. the
request is already being serviced, but data has not arrived).

•

A read request to this address has not yet been accepted by the WXB as a delayed transaction,
there is room to enqueue a new delayed transaction, and the request is enqueued.

•

A read request is to an address that has not yet been accepted by the WXB and there is no more
room to enqueue a new delayed transaction.

•

A write request has insufficient buffering in the WXB to allow it to be posted (e.g. a full line is
not available for MWI).

•

The PCI interface is LOCKED from the host side, unless the transaction is a read request and
the data has already been fetched by the WXB.

6.12.8.2.4 Target Abort

The WXB will issue a target abort if a hard fail response is returned over the Expander bus. This
response is limited to inbound read requests.

6.12.8.2.5 Other Violations

The PCI specification identifies numerous cases that are violations of the PCI protocol. Other than
the cases identified above, the WXB makes no attempt to check for such violations. Response to
such violations is undefined. This includes, but is not limited to:

«
...
127
128
129
130
131
...
»

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

Brand: Panasonic Pages: 4

Brand: Datasat Pages: 32

Brand: Renesas Pages: 941

COMMWARE ECHO 5G

Brand: pivotal Pages: 2

Brand: H3C Pages: 9

Brand: Idis Pages: 22

Brand: NCR Pages: 15

Brand: ZiLOG Pages: 11

Brand: FiberHome Pages: 2

netHOST NHST-T100

Brand: hilscher Pages: 75

NexXxoS GPX-N 1070-M08

Brand: Alphacool Pages: 4

Brand: HighPoint Pages: 12

Brand: M86 Security Pages: 512

iConverter GX/F

Brand: Omnitron Systems Technology Pages: 2

Brand: Renesas Pages: 52

Brand: D-Link Pages: 2

Brand: 4ms Company Pages: 4

Brand: Lenze Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands