Intel 460GX Software Developer’S Manual Download Page 248 | Manualshive

Page: 248 / 294

background image

Universal Serial Bus (USB) Configuration

13-4

Intel® 460GX Chipset Software Developer’s Manual

13.2.6

CLASSC–Class Code Register (Function 2)

Address Offset:

0A-0Bh

Default Value:

0C03h

Attribute:

Read only

This register identifies the Base Class Code, Sub-Class Code, and Device Programming interface
for IFB PCI Function 2.

13.2.7

MLT–Master Latency Timer Register (Function 2)

Address Offset:

0Dh

Default Value:

00h

Attribute:

Read/Write

MLT is an 8-bit register that controls the amount of time (in terms of PCI clocks) the USB module
can do transactions on the PCI bus. The count value is an 8 bit quantity, however MLT[3:0] are
reserved and assumed to be 0 when determining the count value. MLT is used when the USB
module becomes the PCI bus master and is cleared and suspended when IFB is not asserting
FRAME#. When IFB asserts FRAME#, the counter is enabled and begins counting. If the serial
bus module finishes its transaction before count is expired, the MLT value is ignored. If the count
expires before the transaction completes, IFB initiates a transaction termination as soon as the
current transaction is completed.. The number of clocks programmed in the MLT represents the
time slice (measured in PCI clocks) allotted to IFB, after which it must surrender the bus as soon as
the current transaction is completed.

13.2.8

HEDT–Header Type Register (Function 2)

Address Offset:

0Eh

Default Value:

00h

Attribute:

Read only

This register identifies the Serial Bus module as a single Function device.

Bit

Description

23:16

Base Class Code (BASEC). 0Ch=Serial Bus controller.

15:8

Sub-Class Code (SCC). 03h=USB Host Controller..

7:0

Programming Interface (PI). 00h=Universal Host Controller Interface.

Bit

Description

7:4

Master Latency Counter Value. IFB initiated PCI cycles (including multiple transactions) can last
indefinitely as long as PHLDA# remains active. However, if PHLDA# is negated after a transaction
is initiated, IFB limits the duration of the transactions to the number of PCI bus clocks specified by
this field.

3:0

Reserved.

Bit

Description

7:0

Device Type (DEVICET). 00. Multi-Function device capability for IFB is defined by the HEDT
register in Function 0.

«
...
246
247
248
249
250
...
»

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

NetLink 2960 RAS

Brand: Patton electronics Pages: 2

SmartMedia Adapter PC Card REX-SMA01F

Brand: Ratoc Systems Pages: 75

Brand: Dahua Pages: 6

Armor 101 Series

Brand: Lochinvar Pages: 28

Armor 101 Series

Brand: Lochinvar Pages: 44

Brand: SIIG Pages: 12

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: hilscher Pages: 154

Brand: Lanner Pages: 63

Brand: Seattle Computer Products Pages: 31

Brand: M86 Security Pages: 309

Brand: VCS Pages: 118

Brand: Observint Pages: 117

Brand: Alesis Pages: 11

Brand: NXP Semiconductors Pages: 1202

Brand: Altimium Pages: 12

Brand: ADTRAN Pages: 2

Brand: Aim Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands