Intel 460GX Software Developer’S Manual Download Page 141 | Manualshive

Page: 141 / 294

background image

Intel® 460GX Chipset Software Developer’s Manual

7-11

AGP Subsystem

When a DRC is valid in the GXB, a 2

15

PCI clock timer is started as described in the PCI 2.2

Specification. When the timer expires the DRC is discarded and the associated delayed read
matching registers are cleared. This condition is optionally treated as an error. See the “Error”
Chapter for details.

7.2.7.5

Inbound I/O Reads

I/O reads on the PCI bus are not claimed by the GXB.

7.2.7.6

Inbound Writes

Memory write requests may be directed to the memory only. All write requests are posted. A series
of buffers in both the GXB and SAC allow posted writes to be accumulated and serviced as
convenient. The actual data is forwarded to buffers in the SAC, where it is held until the request
can be snooped on the system bus.

Writes to Memory

The snoops on the system bus for PCI Stream AGP-DRAM writes will be initiated by using the
Memory Read and Invalidate of Length=0 system bus transaction. Any implicit write back due to
snoop hit to a modified line will be snarfed by the SDC. The write back data will be merged with
the AGP write data within the SDC.

Writes to memory use the linear burst ordering provided on the AGP bus.

The Write and Write & Invalidate commands have small differences, as follows:

Write

Accumulates posted data until (a) a cache line boundary is reached, or (b) the
master disconnects, before forwarding the request to the SAC. The SAC
therefore deals with a single packet that represents up to a cache line of data.
The SAC places a cache-line snoop on the bus, and the SDC handles the writing/
merging of the partial data into memory. The Expander bus command is a write.

Write & Invalidate By definition this must be an aligned cache line worth of data. It is forwarded

to the SAC as a cache line of data. The SAC places a cache-line snoop on the
bus for each line of data, and the SDC writes the full cache line into memory.
In the event the snoop results in a HITM#, the write back data from the
processor is discarded by the SDC.

Note that the actual writing of the data into memory may be delayed. However, in effect, the data
can be counted as being written in the memory, since no other write to that location may pass this
write.

7.2.7.7

Inbound I/O Writes

I/O writes on the PCI bus are not claimed by the GXB.

Table 7-2. Delayed Read Matching Criteria

Command

Address

BEs

Any Memory Read

Match

Match

«
...
139
140
141
142
143
...
»

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

Brand: 3Com Pages: 8

Brand: National Instruments Pages: 11

ILDA Gem Laser projector tool

Brand: Stanwax Laser Pages: 3

Brand: IBA Pages: 29

TWR-SB0410-36EVB

Brand: NXP Semiconductors Pages: 26

EXPANSION CARD X-DANTE

Brand: Behringer Pages: 65

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: Xmart Pages: 8

Brand: Marani Pages: 39

2000 IDU Series

Brand: EMS Pages: 52

Brand: Kramer Pages: 2

Brand: COUGAR Pages: 2

Brand: ICOP Technology Pages: 42

Brand: UMAX Technologies Pages: 27

Brand: Jetter Pages: 20

Brand: MEN Pages: 48

Brand: Disc Makers Pages: 12

Brand: LanReady Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands