Intel 460GX Software Developer’S Manual Download Page 189 | Manualshive

Page: 189 / 294

background image

Intel® 460GX Chipset Software Developer’s Manual

10-19

IFB Usage Considerations

10.6

USB Resume Enable Bit

Two bits have been added to the USB Host controller functionality in function 2 of IFB (PCI
Register configuration space at Offset C4h). This register is in the resume well of this function.

USB Resume Enable: (IFB Function 2 Config Register)

Address Offset:

C4h

Attribute:

Read/Write

Default Value:

00h

Size:

8 bits

For performing legacy power management, the firmware has to set these two bits in each of the
functions, if it wants the USB Host controller to monitor these ports.

Interrupt/Activity Status Combinations

Bit 2

Bit 0

Description

0

1

DMA transfer is in progress. No interrupt has been generated by the IDE device.

1

0

The IDE device generated an interrupt and the Physical Region Descriptors
exhausted. This is normal completion where the size of the physical memory regions is
equal to the IDE device transfer size.

1

1

The IDE device generated an interrupt. The controller has not reached the end of the
physical memory regions. This is a valid completion case when the size of the physical
memory regions is larger than the IDE device transfer size.

0

0

Error condition. If the IDE DMA Error bit is 1, there is a problem transferring data to/
from memory. Specifics of the error have to be determined using bus-specific
information. If the Error bit is 0, the PRD specified a smaller buffer size than the
programmed IDE transfer size.

Bit

Type

Description

7:2

RO

Reserved

1

RW

PORT1EN: Enable port 1 of the USB controller to look at wakeup events. When set, the
USB controller will monitor port 1 for remote wakeup and connect/disconnect events.
When cleared, the USB controller will not look at this port for a wakeup event. For function
2, this bit applies to port 1.

0

RW

PORT0EN: Enable port 0 of the USB controller to look at wakeup events. When set, the
USB controller will monitor port 0 for remote wakeup and connect/disconnect events.
When cleared, the USB controller will not look at this port for a wakeup event. For function
2, this bit applies to port 0.

«
...
187
188
189
190
191
...
»

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

Brand: PaloAlto Networks Pages: 3

Brand: Grizzly Pages: 9

CNPS7000A Series

Brand: ZALMAN Pages: 9

D-NVR4108HS-4KS2/L

Brand: Dahua Pages: 33

CNPS5X PERFORMA

Brand: ZALMAN Pages: 8

Brand: Symantec Pages: 100

Accelero TWIN TURBO II

Brand: Arctic Pages: 2

Brand: RR-Concepts Pages: 12

Brand: Omron Pages: 14

Brand: Cypress Semiconductor Pages: 28

MTDOT-868 Series

Brand: Multitech Pages: 60

CP 040 RS422/485

Brand: YASKAWA Pages: 87

Brand: Westermo Pages: 22

Brand: CAME Pages: 14

Brand: Cabletron Systems Pages: 54

MEITRACK MVT380

Brand: Shenzhen Pages: 8

Brand: iSMA Pages: 19

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands