Intel 460GX Software Developer’S Manual Download Page 267 | Manualshive

Page: 267 / 294

background image

Intel® 460GX Chipset Software Developer’s Manual

14-9

SM Bus Controller Configuration

14.3.4

smbhstcmd–SMBus Host Command Register (I/O)

I/O Address:

Base + (03h)

Default Value:

00h

Attribute:

Read/Write

This register is transmitted by the SMBus controller host interface in the command field of the
SMBus protocol.

14.3.5

smbhstadd–SMBus Host Address Register (I/O)

I/O Address:

Base + (04h)

Default Value:

00h

Attribute:

Read/Write

This register is transmitted by the SMBus controller host interface in the slave address field of the
SMBus protocol.

14.3.6

smbhstdat0–SMBus Host Data 0 Register (I/O)

I/O Address:

Base + (05h)

Default Value:

00h

Attribute:

Read/Write

This register is transmitted by the SMBus controller host interface in the Data0 field of the SMBus
protocol.

Bit

Description

7:0

SMBus Host Command (HST_CMD)–R/W. This field contains the data transmitted in the
command field of SMBus host transaction.

Bit

Description

7:1

SMBus Address (SMB_ADDRESS)–R/W. This field contains the 7-bit address of the targeted
slave device.

0

SMBus Read or Write (SMB_RW)–R/W. 1 = Execute a READ command. 0 = Execute a WRITE
command.

Bit

Description

7:0

SMBus Data 0 (SMBD0)–R/W. This register should be programmed with the value to be
transmitted in the Data0 field of an SMBus host interface transaction. For a block write
command, the count of the memory block should be stored in this field. The value of this register
is loaded into the block transfer count field. This register must be programmed to a value
between 1 and 32 for block command counts. A count of 0 or a count above 32 will result in
unpredictable behavior. For block reads, the count received from the SMBus device is stored
here.

«
...
265
266
267
268
269
...
»

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

Brand: Yaesu Pages: 2

Brand: RadiSys Pages: 44

Brand: Acqiris Pages: 22

PCH1 T P Series

Brand: Parker Pages: 107

Brand: UfiSpace Pages: 35

Brand: Point of View Pages: 13

iTRON B 70.2040

Brand: JUMO Pages: 41

Brand: Omron Pages: 13

Brand: MEDIATEK Pages: 166

Power System H924

Brand: IBM Pages: 48

XC-16CH-NVR-4TB

Brand: Xyclop Pages: 19

Brand: Patton electronics Pages: 8

Brand: LevelOne Pages: 49

Brand: Air Live Pages: 2

STEVAL-SCR002V1

Brand: ST Pages: 28

Internal All-in-One Digital Media Drive ULT31793

Brand: Ultra Products Pages: 1

Brand: LevelOne Pages: 142

Brand: Brickcom Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands