Intel 460GX Software Developer’S Manual Download Page 15

Page: 15 / 294

Intel® 460GX Chipset Software Developer’s Manual

1-3

Introduction

1.2

Product Features

1.3

Itanium™ Processor System Bus Support

•

Full support for the Itanium processor system bus.

— 64-bit data bus.

— 266 MHz data bus frequency.

— Cache line size of 64 bytes.

— Supports SAPIC interrupt protocol.

•

Full support for 4-way multiprocessing.

•

Parity protection on address and control signals, ECC protection on the data signals.

•

GTL+ bus driver technology.

•

High performance hardware based on IA-64
architecture

— 4.2 GB/s memory bandwidth can

simultaneously support both the full system
bus and the full I/O bus bandwidths

— Architectural support for 64 MB to 64 GB of

SDRAM

— Support for up to four bridge chips that

interface to the 82461GX (SAC) through
four Expander channels, each 30 bits wide
and providing 533 MB/s peak bandwidth

— AGP 4X compatible, via the 82465GX

(GXB) and two Expander channels running
at 266 MHz totaling 1 GB/s peak bandwidth

— Support for two 64-bit, 66-MHz PCI buses

using one 82466GX (WXB) component per
Expander channel

— Support for two independent 32-bit, 33-MHz

PCI buses or one 64-bit, 33-MHz PCI bus via
the 82467GX (PXB) per Expander channel

— Data streaming support between Expanders

and DRAM, up to 533 MB/s per Expander
channel

•

Extensive RAS features for mission-critical
needs

— ECC protection on the system bus data

signals

— Memory ECC with single-bit error

correction, double and nibble error detection

— Address and data flows protected by parity

throughout chipset

— ECC bits in DRAM accessible by diagnostics
— Fault recording of multiple errors; sticky

through reset

— JTAG TAP port for debug and boundary scan

capability

— I2C slave interface for viewing and

modifying specific error and configuration
registers

— Bus, memory and I/O performance counters
— Support of ACPI/DMI functions (support is

provided in the IFB)

•

High bandwidth system bus for multiprocessor
scalability

— Support of the Intel® Itanium™ processor

64-bit data bus

— Full support for 4-way multiprocessing
— 266 MHz data bus frequency
— Cache line size of 64 bytes
— Enhanced defer feature for out-of-order data

delivery using IDS#

— AGTL+ bus driver technology

•

Features to support flexible platform
environments

— Hardware compatible with IA-32 binaries
— AGP address space up to 32 GB supported
— Support for Auto Detection of SDRAM

memory type and mixed memory sizes
allowed between rows

— Supports 16-, 64-, 128- and 256-Mbit

DRAM devices

— Full support for the PCI Configuration Space

Enable (CSE) protocol to devices on all
Expander channels

— WXB supports 3.3 volt PCI bus operation

(supports universal and 3.3 volt PCI cards)
and has an Integrated Hot-Plug Controller**

— PCI Rev. 2.2 compliant on the WXB and

PXB

— GXB supports fast writes and 1x, 2x and 4x

data rates

— 1 MB or greater of firmware storage

provided by the 82802AC (FWH)

— Interrupt controller, bus-mastering IDE and

Universal Serial Bus supported by the
82468GX (IFB)

— Support of 8259A mode, APIC mode and

SAPIC mode interrupts via the
UPD55566S1-016 (PID) provided by NEC*

**Based on technology licensed from Compaq Computer Corp.

Summary of Contents for 460GX







































































































































































































































































































Search results

Summary of Contents for 460GX

Reviews:

Related manuals for 460GX

Brands by name

Popular brands

Intel 460GX, Software Developer’S Manual

Search results

Summary of Contents for 460GX

Reviews:

Related manuals for 460GX

Brands by name

Popular brands