manualshive.com logo in svg

Intel 460GX, Software Developer’S Manual

The Intel 460GX Software Developer’s Manual is an essential resource for software developers, providing detailed insights into the product's features and functionalities. Download this comprehensive manual for free to enhance your understanding and optimize the utilization of the Intel 460GX. Get it now from our website!

Share
Download
background image

Data Integrity and Error Handling

6-24

Intel® 460GX Chipset Software Developer’s Manual

6.11.4.2.2 GART Interface Errors

•

GART Parity Error - There is one parity bit covering each GART entry. When the GART is 
accessed, parity is checked. If an error occurs, then this bit is set. Parity errors are only 
reported when the access falls within the GART aperture range. This prevents errors being 
reported when the GART entry was not used.

•

GART Entry Invalid - Each GART entry has a valid bit associated with it. If the GART entry 
associated with an AGP address is not marked as valid, then this bit is set. This error is only 
reported when the access falls within the GART aperture range. This prevents errors being 
reported when the GART entry was not used. 

•

Illegal Address - After translation is done, the address is checked. If it is in the range between 
GAPBAS and GAPTOP, or in the VGA range with VGAGE asserted, or directed by the 
MARG’s to PCI instead of memory, or above TOM; then the access is illegal and considered a 
fault. 

•

Illegal Outbound GART Access - Any programming access, read or write, to the GART that is 
not 4B or is not aligned on a 4B boundary. The behavior is undefined for the error. 

6.11.4.2.3 AGP Interface Errors

•

Use of Pipe with Sideband Enabled - The card must not mix sideband and Pipe requests. If 
sideband is enabled and the card attempts an access with PIPE, this error occurs. 

•

AGP Address[63:40] not Equal to Zero - This address is outside the legal graphics aperture 
and is over the TOM, therefore is an error.

•

AGP Request Queue Overflow - The GXB supports 16 AGP transactions. If the card attempts 
to do a new transaction when there are 16 already outstanding, this error is flagged.
Illegal AGP Command - Set whenever the GXB receives an unknown or undefined command 
from the graphics card.

6.11.4.2.4 Data Errors

•

AGP Hi-priority Write Que Data Parity Error - AGP write data was placed in the que with 
good parity. If this error is set, then the write que itself was corrupted. The GXB will not report 
this error with either interrupt or BINIT#. The error is actually reported by the SAC or allowed 
to continue to memory where it will be poisoned. 

•

AGP Low-priority Write Que Data Parity Error - AGP write data was placed in the que with 
good parity. If this error is set, then the write que itself was corrupted. The GXB will not report 
this error with either interrupt or BINIT#. The error is actually reported by the SAC or allowed 
to continue to memory where it will be poisoned.

•

PCI Inbound Write Que Data Parity Error - PCI write data was placed in the que with parity as 
received from the PCI bus. This error may have occurred because of bad parity on the PCI bus 
or because the que itself was corrupted. The GXB will not report this error with either interrupt 
or BINIT#. The error is actually reported by the SAC or allowed to continue to memory where 
it will be poisoned. 

Note:

On data transfers from the card to the GXB, there may be wait states. If there is a parity error on the 
AD bus when there is a wait state, then the GXB will not flag any error. It only flags an error when 
data is actually captured by the GXB’s PCI interface. 

•

PCI Outbound Read Que Data Parity Error - PCI read data was placed in the que with parity as 
received from the PCI bus. The GXB will not report this error with either interrupt or BINIT#. 
The error is actually reported by the SAC or allowed to continue to memory where it will be 
poisoned.

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Brand: Paradyne Pages: 1
Kontron 50099 067 User Manual preview
50099 067
Brand: Kontron Pages: 42
Hama 00176547 Operating Instruction preview
00176547
Brand: Hama Pages: 25
Arctic Accelero TWIN TURBO II Installation Manual preview
Accelero TWIN TURBO II
Brand: Arctic Pages: 2
McIntosh MX160 Owner'S Manual preview
MX160
Brand: McIntosh Pages: 44
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Brand: Avigilon Pages: 12
NEC N8154-25 User Manual preview
N8154-25
Brand: NEC Pages: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Brand: Renesas Pages: 28
Lattice Semiconductor mVision AR0234 User Manual preview
mVision AR0234
Brand: Lattice Semiconductor Pages: 25
silicom TimeSync STS2 Hardware Installation Manual preview
TimeSync STS2
Brand: silicom Pages: 16
MACHINIST X79-Z9-D7 User Manual preview
X79-Z9-D7
Brand: MACHINIST Pages: 15
peplink Balance 380 User Manual preview
Balance 380
Brand: peplink Pages: 111
Adeunis RF COMFORT LwM2M User Manual preview
COMFORT LwM2M
Brand: Adeunis RF Pages: 68
Aprotech INTEL CORE i5 SYSTEM BOARD User Manual preview
INTEL CORE i5 SYSTEM BOARD
Brand: Aprotech Pages: 154
Toshiba AD368 User Manual preview
AD368
Brand: Toshiba Pages: 38
Sanyo CPH5802 Brochure preview
CPH5802
Brand: Sanyo Pages: 19
Huawei RT-FIC-1GBE Specifications preview
RT-FIC-1GBE
Brand: Huawei Pages: 3
Huawei RT-FIC-4SAE Specifications preview
RT-FIC-4SAE
Brand: Huawei Pages: 2

Brands by name

Popular brands

Load more brands