Intel 460GX Software Developer’S Manual Download Page 58 | Manualshive

Page: 58 / 294

background image

Register Descriptions

2-38

Intel® 460GX Chipset Software Developer’s Manual

5:0

Event Selection
This field specifies the basic PCI bus transaction or PCI bus signal to be monitored.

All other encodings are reserved.

NOTE:1. Counting data cycles is undefined for this selection.

2.5.4

GXB

2.5.4.1

AGP_PMD_0,1: AGP Performance Monitor Data Registers

Function Number:

BFN+1

Address Offset:

50h, 58h

Size:

64 bits

Default Value:

0

Attribute:

Read/Write

Sticky:

No

Locked:

No

This counter may be configured to track AGP bus events as well as events internal to the GXB.
Event detection may be configured to increment a counter, affect performance monitoring pins, and
issue an interrupt request on counter overflow.

The value written to this address, loads the counter and is also saved in a reload register. Each
counter can be configured to reload the data.

The AGP_G_PMD register holds the performance monitoring count value. 39-bits of the counter
are used for event counting, the 40th-bit is used as a overflow detection bit. The 39-bit count value
allows up to 70 minutes of event collection at 133 MHz. Event selection is controlled by the PMC
registers.

Each counter may be stopped/started independently, using the controls available in the associated
PMD register.

Bits

Description

63:40

reserved(0)

39

Overflow
This bit is asserted when the Event Count bit 38 carries into bit 39.

Individual Bus Transactions
00 0000

reserved

00 1000

reserved

00 0001

reserved

00 1001

reserved

00 0010

I/O Read

00 1010

reserved

00 0011

I/O Write

00 1011

reserved

00 0100

reserved

00 1100

Memory Read Multiple

00 0101

reserved

00 1101

Dual Address Cycle

00 0110

Memory Read

00 1110

Memory Read Line

00 0111

Memory Write

00 1111

Memory Write & Invalidate

Generic (Grouped) Bus Transactions
010 000

Any bus transaction

010 100

Any I/O transaction

010 001

Any memory transaction

010 101

Any I/O or memory
transactions

010 010

Any memory read

010 110

Any I/O or memory read

010 011

Any memory write

010 111

Any I/O or memory write

Bus Signal Assertions
011 000

reserved

011 100

reserved

011 001

reserved

011 101

reserved

011 010

RETRY

1

011 110

LOCK

011 011

reserved

011 111

ACK64

«
...
56
57
58
59
60
...
»

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

Brand: National Instruments Pages: 11

Brand: Delta Tau Pages: 74

Brand: Supero Pages: 68

Brand: Hama Pages: 8

Brand: N.A.T. Pages: 32

Brand: Cytron Technologies Pages: 13

Brand: PADAUK Pages: 27

Brand: CAME Pages: 32

Q-SYS QIO-GP8x8

Brand: QSC Pages: 13

Brand: Me Pages: 28

Brand: Renesas Pages: 31

Brand: Terasic Pages: 208

Brand: IBASE Technology Pages: 64

Brand: Lobaro Pages: 26

Xonar HDAV Slim

Brand: Asus Pages: 52

Brand: MikroTik Pages: 7

Brand: ettus Pages: 17

Brand: Toshiba Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands