manualshive.com logo in svg

Intel 460GX, Software Developer’S Manual

The Intel 460GX Software Developer’s Manual is an essential resource for software developers, providing detailed insights into the product's features and functionalities. Download this comprehensive manual for free to enhance your understanding and optimize the utilization of the Intel 460GX. Get it now from our website!

Share
Download
background image

viii

Intel® 460GX Chipset System Software Developer’s Manual

11.1.16 Deterministic Latency Control Register (Function 0)...........................11-7
11.1.17 MGPIOC–Muxed GPIO Control (Function 0) ......................................11-8
11.1.18 PDMACFG–PCI DMA Configuration Resister (Function O)................11-8
11.1.19 DDMABP–Distributed DMA Slave Base Pointer

Registers (Function 0) .........................................................................11-8

11.1.20 RTCCFG–Real Time Clock Configuration Register (Function 0) ........11-9
11.1.21 GPIO Base Address (Function 0)......................................................11-10
11.1.22 GPIO Enable (Function 0) .................................................................11-10
11.1.23 LPC COM Decode Ranges (Function 0) ...........................................11-10
11.1.24 LPC FDD/LPT Decode Ranges (Function 0) ....................................11-11
11.1.25 LPC Sound Decode Ranges (Function 0) .........................................11-12
11.1.26 LPC Generic Decode Range (Function 0).........................................11-12
11.1.27 LPC Enables (Function 0) .................................................................11-13

11.2

PCI to LPC I/O Space Registers ....................................................................11-15
11.2.1 DMA Registers ..................................................................................11-15
11.2.2 Interrupt Controller Registers ............................................................11-20
11.2.3 Counter/Timer Registers ...................................................................11-25
11.2.4 NMI Registers ...................................................................................11-28
11.2.5 Real Time Clock Registers................................................................11-29
11.2.6 Advanced Power Management (APM) Registers..............................11-30
11.2.7 ACPI Registers..................................................................................11-31
11.2.8 SMI Registers....................................................................................11-35
11.2.9 General Purpose I/O Registers .........................................................11-37

12

IDE Configuration..........................................................................................................12-1

12.1

PCI Configuration Registers (Function 1) ........................................................12-1

12.2

IDE Controller Register Descriptions (PCI Function 1) ....................................12-1
12.2.1 VID–Vendor Identification Register (Function 1) .................................12-2
12.2.2 DID–Device Identification Register (Function 1) .................................12-2
12.2.3 PCICMD–PCI Command Register (Function 1) ..................................12-2
12.2.4 PCISTS–PCI Device Status Register (Function 1)..............................12-3
12.2.5 CLASSC–Class Code Register (Function 1).......................................12-3
12.2.6 MLT–Master Latency Timer Register (Function 1)..............................12-4
12.2.7 BMIBA–Bus Master Interface Base Address Register

(Function 1) .........................................................................................12-4

12.2.8 SVID–Subsystem Vendor ID (Function 1)...........................................12-5
12.2.9 SID–Subsystem ID (Function 1)..........................................................12-5
12.2.10 IDETIM–IDE Timing Register (Function 1)..........................................12-5
12.2.11 SIDETIM–Slave IDE Timing Register (Function 1) .............................12-6
12.2.12 DMACTL–Synchronous DMA Control Register (Function 1) ..............12-7
12.2.13 SDMATIM–Synchronous DMA Timing Register (Function 1) .............12-8

12.3

IDE Controller I/O Space Registers .................................................................12-9
12.3.1 BMICx–Bus Master IDE Command Register (I/O) ..............................12-9
12.3.2 BMISx–Bus Master IDE Status Register (I/O)...................................12-10
12.3.3 BMIDTPx–Bus Master IDE Descriptor Table Pointer Register (I/O) .12-11

13

Universal Serial Bus (USB) Configuration.....................................................................13-1

13.1

PCI Configuration Registers (Function 2) ........................................................13-1

13.2

USB Host Controller Register Descriptions (PCI Function 2) ..........................13-2
13.2.1 VID–Vendor Identification Register (Function 2) .................................13-2
13.2.2 DID–Device Identification Register (Function 2) .................................13-2
13.2.3 PCICMD–PCI Command Register (Function 2) ..................................13-2

Summary of Contents for 460GX







































































































































































































































































































Reviews:

No comments

Related manuals for 460GX

Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
EAW MX8600 Jumpstart Manual preview
MX8600
Brand: EAW Pages: 6
EAW UX8800 Technical Note preview
UX8800
Brand: EAW Pages: 6
Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Brand: Jetter Pages: 35
3Ware 9550SX Series Installation Manual preview
9550SX Series
Brand: 3Ware Pages: 4
Aqua Computer Aquaduct 240 eco Operating And Assembly Manual preview
Aquaduct 240 eco
Brand: Aqua Computer Pages: 20
NAMCO SOUL CALIBUR II Manual preview
SOUL CALIBUR II
Brand: NAMCO Pages: 26
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Brand: V-Count Pages: 2
Digi DataFire GO! PRO Manual preview
DataFire GO! PRO
Brand: Digi Pages: 20
Kontron AdvancedTCA AT8901M User Manual preview
AdvancedTCA AT8901M
Brand: Kontron Pages: 76
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Brand: VIA Technologies Pages: 25
Uctronics U6187 Assembly Manual preview
U6187
Brand: Uctronics Pages: 12
Moxa Technologies Smartio CP-104UL Quick Installation Manual preview
Smartio CP-104UL
Brand: Moxa Technologies Pages: 2
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Brand: Broadband Products Pages: 16
ZALMAN CNPS9700 LED User Manual preview
CNPS9700 LED
Brand: ZALMAN Pages: 8
c SwiftreaderX Installation Manual preview
SwiftreaderX
Brand: c Pages: 32
artisan PB-SIO4A Manual preview
PB-SIO4A
Brand: artisan Pages: 36
G&D ControlCenter-IP 2.0 Installation Manual preview
ControlCenter-IP 2.0
Brand: G&D Pages: 60

Brands by name

Popular brands

Load more brands