manualshive.com logo in svg

Inspur Tiansuo TS860, User Manual

Share
Download
Inspur Tiansuo TS860 User Manual Download Page 68

Chapter 7 Common Problems and Troubleshooting

64

3. For special needs, when moving the server, pay attention to avoiding the 

vibration and carry out in power-off condition.

4. For more notices of our products, please refer to the FAQ for server in the 

official website of Inspur: http://www.inspur.com 

7.4 Technical Support Information

If you have questions or encounter insoluble problem in the process of using 
Inspur server, please take the following measures:

1. If you have problems about product configuration and detailed specification, 

please contact your supplier. 

2. If system problem occurs during the use of the machine, please contact Inspur 

server customer service center. Please record serial number on the host chassis, our 
technical support staff will provide you with the solution or on-site service after 
receiving your service request. 

3. Inspur server customer service center contact information:
Technical support telephone: 400-8600011
Email: [email protected]
Inspur server driver and product material download link:
http://www.inspur.com (search related content in the “support download” column)

Summary of Contents for Tiansuo TS860





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands