manualshive.com logo in svg

Inspur Tiansuo TS860, User Manual

Share
Download
Inspur Tiansuo TS860 User Manual Download Page 41

Chapter 4 Operating System Installation

37

4.2.2 Installation steps

1. Connect USB drive to the server. Power up and start the system, put the 

installation disk into the optical drive (here taking using DVD installation disk as 
example), enter BIOS setup and select to boot from the CD.

2. System enters the interface of “Welcome to Red Hat Enterprise Linux 6.4!” 

there are the following options:

 Install or upgrade an existing system
 Install system with basic video driver
 Rescue installed system
 Boot from local driver
Use up and down arrow keys to select the option, here the default is the first 

installation, select “Install or upgrade an existing system”, press <Enter> to continue 
the installation.

3. System prompts “Disc Found, To begin testing the media before installation 

press OK. Choose Skip to skip the media test and start the installation.”

Select <Skip> to evade the disk detection and press <Enter> to continue the 

installation.

4. Enter the interface of “Red Hat Enterprise Linux 6”, click <Next> to continue 

the installation.

5. System enters the interface of “What language would you like to use during the 

installation process?” Select language version of the operating system. Here we select 
“English (English)” for installation and click <Next> to continue the installation.

6. System enters “Select the appropriate Keyboard for the system” interface. Here 

we select “U.S. English” and click <Next> to continue the installation.

7. System enters the interface of “What type of devices will your installation 

involve?

Basic Storage Devices
Installs or upgrades to typical type of storage devices. If you’re not sure which 

option is right for you? This is probably it.

Specialized Storage Devices
Installs or upgrades to enterprise devices such as Storage Area Networks (SANs).

This option will allow you to add Foe/Ischia/Zech disks and to filter out devices the 

installer should ignore.”

Summary of Contents for Tiansuo TS860





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands