manualshive.com logo in svg

Inspur Tiansuo TS860, User Manual

Share
Download
Inspur Tiansuo TS860 User Manual Download Page 42

Chapter 4 Operating System Installation

38

Here we select “Basic Storage Devices”, and press <Next> to continue the 

installation.

8. System enters the interface of “Please name this computer. The hostname 

identifies the computer on a network.”

Please input the Hostname. Here you can select the [Configure Network] at the 

left bottom of this window to set network configuration, including adding or deleting 
NIC and configuring network IP address. After network configuration is finished, press 

<Next> to continue the installation.

9. The installation program enters “Please select the nearest city in your time 

zone” time zone selection interface, select “Asia/shanghai” and click <Next> to 
continue the installation.

10. The installation program enters “Root Password” setting interface, set at least 

six characters as needed and click <Next> to continue the installation.

The root account is used for administering the system. Enter a password for the 

root user.

11. The installation program enters “Which type of installation would you like?” 

interface; there are the following installation options:

Use All Space 
Replace Existing Linux System(s)
Shrink Current System
Use Free Space
Create Custom Layout
This installation takes custom layout as an example, select “Create Custom 

layout”, click <Next> to continue the installation.

12. The installation program enters install hard disk interface. In the list of “Data 

Storage Devices (to be mounted only)”, system will display the detected storage 
devices. Please select the hard disk that needs to install system, add this hard disk to the 
list of “Install Target Devices”, select one hard disk as “Boot Loader”, and then click 
<Next> to continue the installation.

13. The installation program enters partition creating interface of “Please Select A 

Device” (if partition has been created on the hard disk, it will be displayed, and you can 
delete it if you do not need it).

Double click the Free partition and other existing partitions under hard disk, or 

Summary of Contents for Tiansuo TS860





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands