manualshive.com logo in svg

Inspur Tiansuo TS860, User Manual

Share
Download
Inspur Tiansuo TS860 User Manual Download Page 66

Chapter 7 Common Problems and Troubleshooting

62

directly from the attached RAID card driver CD) and whether there is fault in the USB 

flash disk.

7.2.4 Keyboard and mouse do not work

1. Check whether the cable joint of the mouse and keyboard is plugged and 

connected correctly. Make sure the joint pin has no curve.

2. Check whether the mouse setting in the control panel of the operating system is 

correct or not.

3. It is suggested that you use the keyboard and mouse tested for compatibility by 

Inspur or replace with other keyboard and mouse for testing.

7.2.5 System blue screen, halt or restart

For blue screen, restart or halt of the machine in the using of windows system, you 

may resort to the following measures:

1. If other external non-Inspur components or some application program software 

are installed before the fault, it is suggested removing it and going on to test your 
server.

2. Use the latest antivirus software for antivirus test.
3. It is suggested that you record the displayed information code for blue screen, 

such as: stop c000000218.....; stop: 0x0000007b. This kind of information reveals 
problems in the system. It is suggested that you reinstall it. Please refer to this manual 
or call 4008600011 for help.

4. If all above operations fail to solve the problem, it is suggested that you 

backup the file winnt/minidump in disk C, and call the service center for support 

from professional technical engineers who may ask you to provide minidump file for 

further analysis on the cause for blue screen and halt. If there is no minidump folder 
in disk c, please refer to the following steps: right-click on My Computer, select 

<Property>→<advanced>→<startup and recovery>, then select <settings>, change 

<write debugging information> in the next page to “small RAM dump” and restart the 

machine. The system will produce minidump file automatically in the next blue screen.

7.2.6 Machine alarm

If there’s machine alarm in startup or using process, please refer to the following 

measures:

1. If this happens after you inserting some external board cards, you may need to 

Summary of Contents for Tiansuo TS860





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands