manualshive.com logo in svg

Inspur Tiansuo TS860, User Manual

Share
Download
Inspur Tiansuo TS860 User Manual Download Page 45

41

Chapter 5 Integrated Management Functions 

Introduction

This product integrates remote management card, you can remote login the server 

through remote management card. Following gives an introduction of integrated remote 
management card.

5.1 Remote login

1. Remote client server system requirements
The requirements for client server system connected to GUI interface through Web 

browser are as follows:

Requirements

Remote web console/ client server

OS

Support Microsoft Internet Explorer 

Browser 

Support windows browser, chrome browser is suggested

Browser plug-in

Install Java SE Runtime Environment 6

，

Update 12or 

higher version

TCP/IP network protocol stack Support TCP/IP network protocol stack

Browser plug-in download link:

Java SE Runtime Environment: http://www.java.com/en/download/   
2. It needs to set remote client server IP and management card IP in the same 

network segment, the corresponding management card default IP (192.168.0.62), and 
the remote client server IP can be set as:

IP: 192.168.0.63   gateway: 192.168.0.1   subnet mask: 255.255.255.0  

management  card  (BMC)  IP  address  can  be  modified  and  set  in 

“Configuration”→ “network” menu by remote logging in management web 
interface.

Two options in “Lan Interface” correspond as follows respectively:
Management network: correspond to management card
System network: correspond to integrated network card.

Summary of Contents for Tiansuo TS860





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands