INGENIA Nix series Product Manual Download Page 116

Page: 116 / 124

Nix Product Manual |

Dimensions and Assembly

INGENIA | 01/22/2019

116

8 Dimensions and Assembly

The Nix Servo Drive is available in 4 versions, each one with different specifications and dimensions:

•

NIX-x/xx-y-C (Nix with onboard connectors)

•

NIX-x/xx-y-P (Nix with gold plated pin headers)

•

NIX-x/xx-y-Q (Nix with Quick connector board)

•

NIX-x/xx-E-C (Nix with EtherCAT)

8.1 NIX-x/xx-y-C (Nix with onboard connectors)

Nix Servo Drive version NIX-x/xx-y-C has a 60 mm x 75 mm footprint and a maximum 14.5 mm height. The drive is

provided with 4 x Ã˜ 3.2 mm holes for M3 standoff mounting to the drive plate and to allow mounting the EtherCAT

Daughter Board and the IO Starter Kit. These holes are plated and connected to protective earth (PE). The drive

plate is provided with 4 x Ã˜ 3.2 mm M3 holes for fixing or heatsink mounting (if needed). 3D models can be

downloaded

here

Next figure shows mechanical dimensions in

. Tolerances

‰

¤ Â±0.2 mm

Fixation elements diameter â

‰

¤ 6 mm

Please do not use spacers, washers or nuts exceeding 6 mm external diameter as they could collide with
some electrical parts.

Also, take due precautions not to damage any components during assembly.



Summary of Contents for Nix series





























































































































Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands

INGENIA Nix series, Product Manual

Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands