INGENIA Nix series Product Manual Download Page 108

Page: 108 / 124

Nix Product Manual |

Wiring and Connections

INGENIA | 01/22/2019

108

7.7.2 RS485 interface

Nix Servo Drive supports

full duplex RS-485

. This means that independent differential lines are used for TX and RX,

which cannot be connected together.

Full-duplex RS485 is fully compatible with RS422 communication.

Main specifications of Nix RS485 interface are shown in the next table:

Interface

Full duplex
Non-isolated
Self-supplied (no need for external supply)

Communication distance

Up to 1200 m

Baud rate

100 kbps to 10 Mbps

Daisy chain

Supported

Termination resistor

Nix version 1.1.0: 120Î© on RX line included.

Nix version 1.2.0 (Release Feb 2017): Resistor 120 Î© on TX and RX lines included.

Specification

Details

Next figure illustrates how to connect Nix Servo Drive with a host in a point to point configuration.

USB EMI sensitivity

USB is not a rugged interface, and is sensitive to EMI. For the NIX-5/170 use a good quality cable shorter
than 1 m to avoid communication problems while the power stage is enabled.



Multi-point connection

Nix Servo Drive RS485 interface is not intended for bus operation, since there is no collision prevention
protocol implemented. However,

multiple drives can be connected to the same master using daisy

chain connection

Multiple drive connection with daisy chain

must be configured using

Ingenia

Motion Lab

suite.

For

allowing multi-point communication

each servo drive must be allocated a unique node ID

, and

daisy

chain option must be enabled.

Please, see

UART configuration

section in

E-Core

documentation for

further information.



Summary of Contents for Nix series





























































































































Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands

INGENIA Nix series, Product Manual

Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands