INGENIA Nix series Product Manual Download Page 5

Page: 5 / 124

Nix Product Manual |

General Information

INGENIA | 01/22/2019

General Information

2.1 Manual revision history

December 2015

Preliminary draft.

February 2016

Manual public release.

Download

April 2016

Added EtherCAT information. Structure improvements.

Download

November 2016

Minor improvements.

Download

February 2017

Aesthetics and structure improvements. Wiring information
improved.

Download

May 2017

Improved PDF export format.

Download

January 2019

Fixed broken images links

Download

Revision

Release Date

Changes

PDF

For the most up to date information use the online

Nix Product Manual

. The PDF manual is generated only after

major changes.

Please refer to product

hardware revisions

page for information on previous hardware revisions and changes.

2.2 Disclaimers and limitations of liability

The information contained within this document contains proprietary information belonging to

INGENIA-CAT S.L.

Such information is supplied solely for the purpose of assisting users of the product in its installation.

INGENIA-CAT S.L.

rejects all liability for errors or omissions in the information or the product or in other

documents mentioned in this document.

The text and graphics included in this document are for the purpose of illustration and reference only. The
specifications on which they are based are subject to change without notice.

This document may contain technical or other types of inaccuracies.The information contained within this

document is subject to change without notice and should not be construed as a commitment by

INGENIA-CAT

S.L.

INGENIA-CAT S.L.

assumes no responsibility for any errors that may appear in this document.

Some countries do not allow the limitation or exclusion of liability for accidental or consequential damages,

meaning that the limits or exclusions stated above may not be valid in some cases.

2.3 Contact

INGENIA-CAT, S.L.
C/ Avila 124, 2-B

08018 Barcelona

SPAIN

Summary of Contents for Nix series





























































































































Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands

INGENIA Nix series, Product Manual

Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands