INGENIA Nix series Product Manual Download Page 26

Page: 26 / 124

Nix Product Manual |

Connectors Guide

INGENIA | 01/22/2019

5.1.3 Micro-Match connectors mating

Most Nix Servo Drive signal connections are based in TE Micro-Match connectors. Two different wiring options can

be used

ribbon cable

and

multi-core crimped cable

Ribbon cable

Ribbon cable mating

Description

TE Micro-Match Male-on-Wire 1.27 mm pitch

Image

Cable

Use 0.5 mmÂ² (24 AWG) flat cable.

PH_A

Motor phase A connection (Positive for DC and voice coils)

PH_B

Motor phase B connection (Negative for DC and voice coils)

PH_C

Motor phase C connection (Do not connected in DC motors and voice coils)

Protective Earth connection

Pin

Name

Description

For Nix version 1.0.0B, the the Motor mating connector is the Supply and shunt mating connector (4
position).

For further information see

Hardware revisions

Summary of Contents for Nix series





























































































































Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands

INGENIA Nix series, Product Manual

Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands