INGENIA Nix series Product Manual Download Page 11

Page: 11 / 124

Nix Product Manual |

Product Description

INGENIA | 01/22/2019

Current sense
resolution

56.65 mA/count

37.39 mA/count

Shunt braking
transistor

Shunt braking transistor on board.

16 A maximum current.

Dimensioning

a Shunt Resistor for Regenerative
Braking

Shunt braking transistor on board.

5 A maximum current.

Cold plate

High heat transfer black anodized aluminum

Power connectors

Pluggable terminal block 3.5 mm pitch / Pin header 3.5 mm pitch

Standby power
consumption

1.5 W (max)

Efficiency

>97% at the rated power and current

Motion control specifications

Motion control
core

Ingenia E-Core with EMCL2

Supported motor
types

•

Rotary brushless (trapezoidal and sinusoidal)

•

Linear brushless (trapezoidal and sinusoidal)

•

DC brushed

•

Rotary voice coil

•

Linear voice coil

Power stage PWM
frequency

20 kHz (default)

80 kHz (alternative PWM frequency,

configurable

)

Current sensing

On phases A, B and C using 4 terminal shunt resistors.

Accuracy is Â± 1% full scale.

10 bit ADC resolution.

Sensors for
commutation

(brushless
motors)

•

Digital Halls (Trapezoidal)

•

Analog Halls (Sinusoidal / Trapezoidal)

•

Quad. Incremental encoder (Sinusoidal / Trapezoidal)

•

PWM encoder (Sinusoidal / Trapezoidal)

•

Analog potentiometer (Sinusoidal / Trapezoidal)

•

Sin-Cos encoder (Sinusoidal / Trapezoidal)

•

Absolute encoder SSI (Sinusoidal / Trapezoidal)

The default value of the PWM frequency has changed from 40 kHz to 20 kHz to
reduce electro-magnetic interferences (EMI).



Summary of Contents for Nix series





























































































































Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands

INGENIA Nix series, Product Manual

Search results

Summary of Contents for Nix series

Reviews:

Related manuals for Nix series

Brands by name

Popular brands