IBM Flex System x440 Compute Node Installation And Service Manual Download Page 302

Page: 302 / 584

Remove CPU 1 and inspect the CPU socket for bent pins.

Swap CPU 1 and CPU 2. If the error goes away, replace the original CPU 1.

If the problem persists, System board may need to be replaced.(Trained service personnel only)

81010202-0701ffff

Numeric sensor [NumericSensorElementName] going low (lower critical) has deasserted.

Explanation:

This message is for the use case when an implementation has detected a Lower Critical sensor going

low has deasserted. A previously low voltage has returned to above its specified threshold (sensor Planar 12V, Planar
3.3V, or Planar 5V).

May also be shown as 810102020701ffff or 0x810102020701ffff

Severity:

Info

Alert Category:

Critical - Voltage

Serviceable:

CIM Information: Prefix:

PLAT and

ID:

0481

SNMP Trap ID:

Automatically notify Support:

User response:

Information only; no action is required.

81010202-2801ffff

Numeric sensor [NumericSensorElementName] going low (lower critical) has deasserted.

Explanation:

The previously low CMOS battery voltage has returned to above its specified threshold.

May also be shown as 810102022801ffff or 0x810102022801ffff

Severity:

Info

Alert Category:

Critical - Voltage

Serviceable:

CIM Information: Prefix:

PLAT and

ID:

0481

SNMP Trap ID:

Automatically notify Support:

User response:

Information only; no action is required.

81010902-0701ffff

Numeric sensor [NumericSensorElementName] going high (upper critical) has deasserted.

Explanation:

A previously high voltage has returned to below its specified threshold (sensor Planar 12V, Planar 3.3V,

or Planar 5V).

May also be shown as 810109020701ffff or 0x810109020701ffff

Severity:

Info

Alert Category:

Critical - Voltage

Serviceable:

CIM Information: Prefix:

PLAT and

ID:

0495

SNMP Trap ID:

Automatically notify Support:

User response:

Information only; no action is required.

81010202-0701ffff • 81010902-0701ffff

290

IBM Flex System x440 Compute Node Types 7917 and 2584: Installation and Service Guide

Summary of Contents for Flex System x440 Compute Node









































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x440 Compute Node

Reviews:

Related manuals for Flex System x440 Compute Node

Brands by name

Popular brands

IBM Flex System x440 Compute Node, Installation And Service Manual

Search results

Summary of Contents for Flex System x440 Compute Node

Reviews:

Related manuals for Flex System x440 Compute Node

Brands by name

Popular brands