Huvitz HRK-7000 User Manual Download

Page: 70 / 97

70 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

Adjustment of measurement position and focus

Ask the examinee to look at the internal fixed target.

Adjust the position so that the pupil shall be in between two(2)

perpendicular bars by moving the operation lever.

Adjust the focus so that the corneal corner can be seen apparently.

NOTE

As adjusting the focus on the iris, it is impossible to measure the radius of pupil exactly.

Measurement

As pushing the measurement button, the window shall be stopped.

button and button in the center is to adjust the movement of left bar,

and button and button in right side is to adjust the movement of right bar.

Move the relevant bar to left/right sides by pushing button or button.

The measured value shall be indicated on the screen of monitor.

Store the measured value by pushing the measurement button.

The measured value is to be inputted beside “1” of right bottom of the screen. It

is to be inputted beside “AVG” of left bottom of the screen as well.

As pushing MODE button, the stopped window is cancelled, and “2” of left

bottom of the screen is to be selected as the bar. Every time pushing MODE

button, “1” or ”2” is to be selected alternatively. If there was an error in “1” which

is the previous measurement, you can select “1” again.

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands