manualshive.com logo in svg

Huvitz HRK-7000, User Manual

Share
Download
Huvitz HRK-7000 User Manual Download Page 41

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A    41

 

 

8.2.

 

Keratometry (KER Mode) 

 

 

It is the mode to measure the corneal curvature solely.   

Do not measure the base curve of hard contact lens in this mode. Please refer to 

CLBC mode in section 8.5 regarding the base curve of hard contact lens. 

 

1.

 

Check whether or not the screen of monitor is in measurement mode. 

2.

 

KER Mode Selection 

-

 

Push MODE button until “KER” is to be indicated on the upper right side of the 

screen. 

3.

 

Perform the same 2, 3 procedure of consecutive measurement of refractive power. 

 

 

8.2.1.

 

Manual Measurement Mode 

 

①

    Perform the adjustment of array and focus as like in the procedure of section 8.1.1. 

 

②

  Measurement 

-

 

Push the measurement button. 

 

-

 

The measurement continues to be performed as you keep pushing the 

measurement button. 

 

-

 

As the measurement is completed, the measured result is to be indicated on the 

screen of monitor. In case of the consecutive measurement, the result of 

previous measurement is to be indicated. 

 

 

 

 

Summary of Contents for HRK-7000


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands