Huvitz HRK-7000 User Manual Download

Page: 86 / 97

86 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

10.

Self diagnosis & Maintenance

10.1.

Before calling for serviceman

In case that abnormality happens or the machine operates abnormally, a warning sign

is to be indicated. In this case, perform the settlements below.

If the machine does not return to the normal condition in spite of the measures below,

contact to the agent where you bought the machine after switching the power off.

①

As the power switch is on

Message

Cause

Method of settlement

Motor Error

Internal abnormality for the

equipment

Re-input the power in 10

seconds after switching it

off. In case that the

message is indicated

again, contact our sales

representative.

EEPROM Error

EEPROM Data Error

System Error

Clock Error

INVALID SETUP DATA —

REF

Abnormality in the internal

data for Refractometry

Please contact our sales

representative.

INVALID SETUP DATA -

KER

Abnormality in the internal

data for Keratometry

Please contact the selling

agent.

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands