manualshive.com logo in svg

Huvitz HRK-7000, User Manual

Share
Download
Huvitz HRK-7000 User Manual Download Page 9

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A    9

 

 

2.2.

 

Safety Symbol 

 

 

The International Electrotechnical Commission (IEC) has established a set of symbols 

for medical electronic equipment which classify a connection or warn of any potential 

hazards. The classifications and symbols are shown below. 

 

I and O on power switch represent ON and OFF respectively. 

Type B Isolated patient connection. 

It indicates the connection of signal input/output. 

This symbol identifies a safety note. Ensure you understand 
the function of this control before using it. Control function 
is described in the appropriate User’s or Service Manual. 

It indicates the year of manufacture and the manufacturer. 

Identifies the point where the system safety ground is 
fastened to the chassis. Protective earth connected to 
conductive parts of Class I equipment for safety purposes.   

Summary of Contents for HRK-7000


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands