Huvitz HRK-7000 User Manual Download

Page: 20 / 97

20 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

5.2.

Explanation on Switches in Front

[Figure 4. Front Section Switches]

1. MODE Button:

A switch to change the mode for measurement

2. DISP Button:

A switch to indicate the measured results on the monitor

3. FOCUS Button:

A switch to change Auto Focus mode.

4. AUTO Button:

A switch to begin to perform the measurement manually or automatically

5. IOL Button:

A switch to measure the eyesight of cataract patients or patients undergone

IOL implantation.

6. FUNC Button:

A switch to change the functions of

③

④

⑤

buttons

7. Comp Button:

Virtual Comparison Function.

8. Z-MAP Button:

A switch to iindicate Zernike Map.

9. VD Button:

To change the VD(Vertex Distance) value.

10. SIZE Button :

To measure size of pupil.

11. ILLUM Button:

To check the status of the cornea, crystalline lens and contact lens by

freezing images

①

②

③

④

⑤

⑥

⑦

⑨

⑩

⑧

⑪

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands