Huvitz HRK-7000 User Manual Download

Page: 52 / 97

52 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

at the bottom of measurement mode indication.

Four(4) boxes are to be indicated in up/down, left/right side of Mire ring. Each box

indicates the proceeding state of measurement on part around cornea. If there is

the measured result around part of cornea where the box is located, the inside of

box is to be full with color: In case of no result, the box is to be indicated as an

empty box. The relevant box indicated at the part around cornea which is

measured now is to flicker.

Direction of part around cornea

Superior (SUP) : Upside from corneal center

Inferior (INF) : Downside from corneal center

Temple (TEM) : To the temple of examinee from corneal center

Nasal (NAS) : To the nose of examinee from corneal center

⑤

Sequence to measure the part around cornea

Measure it following the sequence of TEM -> SUP -> NAS -> INF

In case that the measurement in the direction of part around cornea becomes

difficult, the direction lamp (guidance LED light) is to radiate in order to draw the

examinee’s sight around Mire ring actually. After the examiner shall ask the

examinee to look at the light of direction lamp, then he or she can perform the

measurement by adjusting the focus of Mire ring.

In case of part around cornea (SUP, INF, TEM, NAS),

R1 : Radius of curvature on maximum meridian in periphery

R2 : Radius of curvature on minimum meridian in periphery

AX : Axis on the radius of curvature on maximum meridian in periphery

RM : Average curvature in periphery

EQ :Difference between diopter and corneal center

E : Eccentricity of periphery

You can change the present measurement position by pushing SEL button in

KER-P mode. If the measurement fails at the specific position, in case that re-

measurement is needed, or as checking the measured result, you can change

the present measurement position by consecutively pushing SEL button.

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands