Huvitz HRK-7000 User Manual Download

Page: 21 / 97

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A 21

Installation of Equipment & Preparation of Measurement

1. Release of Lock on Stage Section

Unlock the clamping bolt at the bottom part of Chin-rest of the machine by rotating

it counterclockwise, and change the stage fixing lever behind the joystick to the

direction of UNLOCK.

2. Connection of Power Cable

Put HRK-7000A on the table.

Insert the power cable into power connector

at the bottom of the main body.

After checking that the power of the machine

is off, insert the power plug into the AC outlet

(socket).

3. Inserting Chin Rest Paper

Pull out the pushing pins at left/right sides.

Insert the pushing pins into the holes at

left/right sides of the chin-rest paper.

Stick the chin-rest paper inserted with the

pushing pins onto the Chin-rest.

4. Installation of Printing Paper

Please refer to section 8.2 regarding the sequence of installation of printing paper.

5. Input of Message

Input the contents desirable to be printed such as name or address of hospital,

etc in the memory of message editing monitor in advance at all times.

[ Figure 5. Connection of Power Cable ]

[ Figure 6. Inserting Chin-rest Paper ]

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands