Huvitz HRK-7000 User Manual Download

Page: 33 / 97

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A 33

②

Adjustment of Measurement Position and Focus

Do not insert your hands or fingers between stage and base. Also, make sure that the
examinee should not put his or her hands or fingers there. Hands or fingers can get
injured.

Pull the body of equipment to the front of user by using the operation lever.

Let the right-side eye of examinee appear at the center of monitor screen by

slowly pushing and rotating the operation lever forward. At this time, let the

glittering bright dot come into the core of internal array ring.

Ask the examinee to look at the internal fixed target.

Adjust the focus so that the outline of bright dot can be apparent. If the focus is

adjusted appropriately, the circle symbol appears on the bright dot.

Height Adjustment: Adjust it by rotating the

operation lever or chin-rest lever.

Left/Right Adjustment: Move the operation lever

left and right so that the Outer Alignment Ring is

aligned with the Mire Image

Focus Adjustment: Adjust it to the bright dot by tilting the operation lever

forward/backward.

CAUTION

[ Figure 16. Height Adjustment ]

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands