Huvitz HRK-7000 User Manual Download

Page: 13 / 97

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A 13

2.4.

Safety Precaution

This equipment has been developed and tested in conformity with domestic &

international safety standards and regulations, which guarantees the high stability of

this product. This guarantees a very high degree of safety for this device. The legislator

expects us to inform the user expressively about the safety aspects in dealing with the

device. The correct handling of this equipment is imperative for its safe operation.

Therefore, please read carefully all instructions before switching on this device. For

more detailed information, please contact our Customer Service Department or one of

our authorized representatives.

This equipment must not be used (a) in an area that is in danger of explosions

and (b) in the presence of flammable, explosive, or volatile solvent such as

alcohol, benzene or similar chemicals.

The device should neither be kept nor installed in the place with high humidity.

For the optimal operation, the humidity should be at the range of 30%~75%.

The machine should not be exposed to the place where water splashes, drips

or sprays. Do not place containers containing fluids, liquids, or gases on top of

any electrical equipment or devices

The equipment must be operated only by, or under direct supervision of

properly trained and qualified person/s.

Modifications of this equipment may only be carried out by Huvitz’s service

technicians or other authorized persons.

Customer maintenance of this equipment may only be performed as stated in

the User’s Manual and Service Manual. Any additional maintenance may only

be performed by Huvitz’s service technicians or other authorized persons.

The manufacturer is only responsible for effects on safety, reliability, and

performance of this equipment when the following requirements are fulfilled: (1)

The electrical installation in the respective room corresponds to the

specifications stated in this manual and (2) This equipment is used, operated

and maintained according to this manual and Service Manual.

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands