Huvitz HRK-7000 User Manual Download

Page: 48 / 97

48 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

⑤

Selection of Screen Indication Type

In the measurement mode including the refractive power measurement, you can

designate the sign of astigmatic refractive power in SETUP mode.

Also, you can indicate the measured data of refractive power on the screen

according to VD value in the measurement mode including the refractive power

measurement.

In the measurement mode including corneal curvature measure, you can

designate the screen indication type (R1/R2/AX

K1/K2/AX

AR/CY/AX) in

SETUP mode.

8.3.2.

Auto Measurement Mode

As pushing Auto button in manual measurement mode, it is to be changed to auto

measurement mode.

As the condition of good array between the machine and measured eye is to be

reached, the measurement is to be performed automatically without pushing the

measurement button in Auto measurement mode.

①

Adjust the array and focus as like in procedure 2 of section 8.1.1.

②

The measurement is to be performed automatically as like in procedure 2 of

section 8.1.2.

③

Print the measured result as like in procedure 6 of section 8.1.1.

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands