Huvitz HRK-7000 User Manual Download

Page: 14 / 97

14 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

The manufacturer is not liable for damage caused by unauthorized tampering

with the device(s). Such tampering will forfeit any rights to claim under

warranty.

The equipment may only be used together with accessories supplied by

Huvitz’s. If the customer makes use of other accessories, use them only if

there are usability under technical safety aspects has been proved and

confirmed by Huvitz or the manufacturer of the accessory.

Only persons who have undergone proper training and instructions are

authorized to install, use, operate, and maintain this equipment.

10.

User’s manual or service manual should be kept in the place where the

persons in chare of operation and maintenance can access easily any time.

11.

Do not force cable connections. If a cable does not connect easily, be sure that

the connector (plug) is appropriate for the receptacle (socket). If you cause any

damage to a cable connector(s) or receptacle(s), let the damage(s) be repaired

by an authorized service technician.

12.

Please do not pull on any cable. Always hold on to the plug when

disconnecting cables.

13.

This equipment may be used for the international application related to

Refractometry and Keratometry according to this manual.

14.

Before every operation, proceed with visual inspection on the equipment

exterior to seek any mechanical damage(s) to ensure the proper functioning.

15.

Do not obstruct any ventilation outlet for proper heat dissipation.

16.

In case of any presence of smoke, spark or abnormal noise/smell from the

machine, please power off immediately and pull out the plug.

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands