Huvitz HRK-7000 User Manual Download

Page: 73 / 97

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A 73

9.3.

VIRTUAL COMPARISON Mode

A Virtual comparison Function allows the patient to compare the current

view(uncorrected eye view) with the view corrected by AR measurement.

By changing the distance to the chart, the patient can experience the virtual comparison.

Perform AR measurement.

Press the COMP button

Press the COMP button again(uncorrected eye or LM Data)

SE value of LENS : LENS METER data or uncorrected eye

SE value of REF : corrected eye by AR measurement(The value of AR

measurement can be set by +INC/-DEC buttons)

Pressing the COMP button switches between the corrected view and the

uncorrected view.

If necessary, switch to the view for near vision

Press the near button(40cm)

f necessary, switch to the view with addition power

Pressing the ADD 1.75D)

Pressing the ADD button again cancels the addition power

Press the Exit button to finish the virtual comparison function and return to the

measurement screen.

Measure the other eye in the same manner.

When finishing the measurement, print the data out.

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands