Huvitz HRK-7000 User Manual Download

Page: 61 / 97

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A 61

Button: It is the button to decrease the intensity of Ref LED for one (1) level.

Button: It is the button to increase the intensity of Ref LED for one (1) level.

Measurement Mode Return: As pushing EXIT button, it is to finish Ret. Illum mode,

and to return to the ordinary measurement mode.

8.7.2.

Observation on Retro-Illum

①

Adjustment of brightness of LED to measure refractive power

In order to take a close look at Retro-Illumination image, change the intensity of

LED to measure refractive power by one (1) level using

button and button.

②

Observation on Retro-Illumination Image

Let LED to measure the refractive power to be at incidence to eye while

avoiding the part of opacity in crystalline lens by using the operation lever. It is

effective for observation on Retro-Illumination to let LED light be shed on part

around pupil.

NOTE

In order to protect the patient’s eyes, avoid examining the eyes over 30 seconds.

③

Stopping Image

After adjusting the focus of image by using the operation lever, stop the image

by pushing the measurement button. If the stopped screen is not satisfactory,

stop the image again after returning to the original screen by pushing EXIT

button.

④

Measuring Refractive Power and Stopping Image

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands