Huvitz HRK-7000 User Manual Download

Page: 60 / 97

60 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

[ Figure 31. Retro-Illum. Measure Window ]

MEA : By using the joystick measurement button, you can store the observed

Ret. Illum image and the measured data of sight refractive power in

memory while changing it as a static window.

MODE : It is the button to change the window between [Measure] and [Observe].

AUTO : It is possible to divide the static window of Ret. Illum obtained by

measurement button by two (2), and to show it by enlarging it for each

left/right eye. By using button and button, select the image.

Also, as pushing SEL button, the selected Ret. Illum image is to be

enlarged. As pushing Print button amongst the menus of enlarged

window, it is possible to output the print of Ret. Illum image. If you push

EXIT button, it is to go back to DIS window again.

Summary of Contents for HRK-7000


































































































Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands

Huvitz HRK-7000, User Manual

Search results

Summary of Contents for HRK-7000

Reviews:

Related manuals for HRK-7000

Brands by name

Popular brands