Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 127

Page: 127 / 216

14 WHEELS, TIRES

125

H00935-10

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change the front wheel bearing.

–

Clean and grease shaft seal rings



and mating surfaces



of the spacers.

Long-life grease (

p. 203)

–

Insert the spacers.

S01058-11

–

Lift the front wheel into the fork, position it, and insert the wheel spindle.

The brake linings are correctly positioned.

–

Mount and tighten screw



Guideline

Screw, front wheel spindle

M24x1.5

45 Nm (33.2 lbf ft)

–

Operate the hand brake lever several times until the brake linings are seated correctly

against the brake disc.

–

Remove the motorcycle from the lift stand. (

p. 77)

–

Operate the front brake and compress the fork a few times firmly.

The fork legs straighten.

–

Tighten screws



Guideline

Screw, fork stub

15 Nm (11.1 lbf ft)

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands