Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 115

Page: 115 / 216

13 BRAKE SYSTEM

113

400418-10

–

Check that leaf spring



in the brake caliper and sliding plate



in the brake caliper

support are seated correctly.

–

Insert the new brake linings, insert the pin, and mount the cotter pins.

Info

Always change the brake linings in pairs.

–

Operate the hand brake lever repeatedly until the brake linings are in contact with the

brake disk and there is a pressure point.

V00502-12

–

Correct the brake fluid quantity to level



Guideline

Level



5 mm (0.2 in)

Brake fluid DOT 4 (

p. 200)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilled brake fluid immediately with water.

13.8

Checking the free travel of foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands