Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 116

Page: 116 / 216

13 BRAKE SYSTEM

114

402027-10

–

Move the foot brake lever back and forth between the end stop and the contact to the

foot brake cylinder piston and check free travel



Guideline

Free travel at foot brake lever

3… 5 mm (0.12… 0.2 in)

Info

You will know that contact has been made with the foot brake cylinder piston

when there is increased resistance when you activate the foot brake lever.

» If the free travel does not meet specifications:

–

Adjust the basic position of the foot brake lever.

(

p. 114)

13.9

Adjusting the basic position of the foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands