Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 137

Page: 137 / 216

15 ELECTRICAL SYSTEM

135

15.1

Removing the battery

Warning

Risk of injury

Battery acid and battery gases cause serious chemical burns.

–

Keep batteries out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

Avoid contact with battery acid and battery gases.

–

Keep sparks and open flames away from the battery. Only charge in well-ventilated rooms.

–

In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at least 15

minutes and contact a physician.

Preparatory work

–

Switch off the ignition by turning the ignition key to the

OFF

position.

–

Remove the seat. (

p. 83)

F00564-10

Main work

–

Pull engine electronics control unit



off of the holder and set it to one side.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands