Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 123

Page: 123 / 216

13 BRAKE SYSTEM

121

V00517-10

–

Stand the vehicle upright.

–

Remove screw cap



with membrane



–

Press the brake caliper onto the brake disc by hand in order to push back the brake

piston. Ensure that brake fluid does not flow out of the brake fluid reservoir, extracting

it by suction if it does.

Info

Make sure when pushing back the brake piston that you do not press the

brake caliper against the spokes.

D00955-10

–

Remove cotter pin



, remove pin



toward the left by striking it, and remove the

brake linings.

–

Clean the brake caliper and brake caliper support.

400419-11

–

Check that leaf spring



in the brake caliper and sliding plate



in the brake caliper

support are seated correctly.

–

Insert the new brake linings, insert the pin, and mount the cotter pins.

Info

Always change the brake linings in pairs.

–

Operate the foot brake lever repeatedly until the brake linings are in contact with the

brake disc and there is a pressure point.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands