Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 162

Page: 162 / 216

16 COOLING SYSTEM

160

V00518-12

–

Stand the motorcycle on its side stand on a horizontal surface.

–

Check the coolant level in compensating tank



The coolant level must be between the two markings.

» If the coolant level does not match the specified value:

–

Correct the coolant level.

Coolant (

p. 200)

V00520-11

–

Remove radiator cap



and check the coolant level in the radiator.

The radiator must be filled completely.

» If the coolant level does not match the specified value:

–

Check the coolant level and the reason for the loss.

Coolant (

p. 200)

–

Mount the radiator cap.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands